Maxsun, Portable Gas Stove for Travel and Camping, Outdoor Cooking Gas Stove, Green, Size24.5*20.4*10Cm

Maxan portable gas stove for travel and trips
Model: MS-8000S
Size: 24.5*20.4*10cm
Gas type: butane
Heat input: 2.1 kW
Gas consumption: 150g/h
Hole diameter: 0.55 mm
Overpressure pressure range switch button
Closure: 5.5 bar - 7.0 bar
Color: Green
Advantages:-
- Portable, solid and fixed gas stove
- Small size, stable, convenient to use and store
- This burner may only be used with a butane and propane gas mixture cylinder
- Light and easy to use and carry during outings and camping
alert : -
- Never use this device in an enclosed space such as a tent, camper, car or house.
- This device can produce carbon monoxide which has no odor.
It may cause your death if used indoors
- The accessible parts may get very hot, so keep children away from the stove
- Do not use the burner if it has damaged or damaged seals; Do not use a stove that is leaking, damaged, or not working properly
- The stove must be used away from flammable materials. Minimum distances from adjacent surfaces: 50 cm from the wall, 125 cm from the ceiling
- Place the pan on the pot supports above the stove and adjust the gas flow so that the flame does not burn higher than the pan. The size of the flame can be regulated by turning the control knob (1) between the full and low flow modes

Figure: Notch in valve guide cartridge collar
1. Primer electrode
2. Cartridge cap
3. Cartridge cap
4. Drip pan
5. Fireplace
6. Cartridge lever
1. High/low control knob with piezo ignition
Important :
Read the instructions carefully before use to familiarize yourself with the burner before connecting it to its gas cartridge.
Keep these instructions for future reference.
- This burner should only be used with a MAX MSF-1A / MSF-1 CRV butane cartridge conforming to EN 417. It may be dangerous to attempt to fit other types of gas cartridge.
- Do not use stoves when the ambient temperature is higher than 35°C.
- Do not use the burner when the cartridge container cover is in the open position.
- Release or unplug the gas cartridge after each use.
- One of the two gas cartridges must be removed from the cartridge chamber while only one burner is in operation
For external use only.
Keep children away from the stove.
warning
- Ensure that the seals (between the device and the gas cartridge) are in place and in good condition before connecting the gas cartridge (Fig. 6)
- Do not use the device if the seals are broken or damaged.
- Do not use a device that is leaking, damaged or not working properly.
security device
- The burner is equipped with a safety device that stops the gas flow if the pressure in the cartridge, for example due to overheating, becomes too high
To continue using...
- Push and turn the control knob (7) to the “””” position
- Turn the cartridge lever (6) to the “unlocked” position and remove the cartridge
- Turn the control knob (7) to the ignition position to release any excess pressure inside the valve
- Insert a new cartridge after checking that the cartridge lever (6) is in the “unlocked” position.
(If the new cartridge is not handy, cool the used cartridge with water.)
- The cartridge can only be installed when the control knob (7) is in the “””” position.

warning
- Before inserting the cartridge, always check that the pan support / drip tray has been rotated and placed in the correct vertical position. Operating this appliance with the pot supports in the down position will cause the appliance to overheat and possibly explode

Using the stove for the first time
1. Ensure that the control knob (7) is set to the “”” position by turning it clockwise and that the cartridge lever (6) is “unlocked”.
2. Open the cartridge cap (2) and insert the cartridge, head facing forward, notch pointing up and in line with value guide (Fig. 2)
3. Press the cartridge lever (6) down (Fig. 3) and close the cartridge cover
4. If you hear a “hiss” sound, the cartridge is not installed correctly. Do not attempt to ignite the burner but move the lever (6) to the “UNLOCK” position and repeat step (1-4).
5. Push and turn knob (7) all the way to the ignition position until it clicks. (Fig. 4) Repeat this procedure until the burner ignites.
6. Adjust the control knob to the desired position. (Fig. 5) Never set the cartridge lever (6) to the “UNLOCK” position during use!

after use
1. Turn the control knob (8) to the “”” position.
2. Check if the igniter has gone out before adjusting the cartridge lever (6) to the “unlock” position.
3. When the burner has completely cooled down, for your own safety, remove the cartridge.
4. Turn the control knob (7) to the ignition position to release any excess gas inside the regulator.
5. Put on the red protective cap and always store the gas cartridge in a cool, dry and well-ventilated place.